How To Add LIRC To Ir-keytable Protocols?

Mar 9, 2025 by ADMIN 42 views

**How to Add LIRC to ir-keytable Protocols**

Introduction

In this article, we will explore the process of adding LIRC (Linux Infrared Remote Control) to ir-keytable protocols on Debian and Raspbian systems. This will enable you to issue bash commands on infrared remote control button presses. We will also cover the setup of the IR receiver device, an USB device included in the Anysee e30 Combo plus DVB-T tuner.

Prerequisites

Before we begin, make sure you have the following:

A Debian or Raspbian system installed on your device
An IR receiver device, such as the Anysee e30 Combo plus DVB-T tuner
The necessary cables and connections to connect the IR receiver device to your system

Step 1: Install Required Packages

To add LIRC to ir-keytable protocols, you will need to install the following packages:

lirc (Linux Infrared Remote Control)
ir-keytable (Infrared remote control keytable)
lirc-utils (LIRC utilities)

You can install these packages using the following command:

sudo apt-get update
sudo apt-get install lirc ir-keytable lirc-utils

Step 2: Configure the IR Receiver Device

To configure the IR receiver device, you will need to create a new file in the /etc/lirc directory. This file will contain the configuration settings for the IR receiver device.

Create a new file called anysee_e30.conf in the /etc/lirc directory using the following command:

sudo nano /etc/lirc/anysee_e30.conf

Add the following configuration settings to the file:

begin
  name  anysee_e30
  bits           32
  eps            30
  aeps          100
  one           0
  zero          0
  pointer       up
  repeat       1
  repeat_fast   2
  toggle_bit   0
  space         0
  begin
    name  anysee_e30
    bits           32
    eps            30
    aeps          100
    one           0
    zero          0
    pointer       up
    repeat       1
    repeat_fast   2
    toggle_bit   0
    space         0
  end
end

Save and close the file.

Step 3: Load the LIRC Module

To load the LIRC module, you will need to create a new file in the /etc/modules directory. This file will contain the module settings for LIRC.

Create a new file called lirc.conf in the /etc/modules directory using the following command:

sudo nano /etc/modules/lirc.conf

Add the following module settings to the file:

lirc

Save and close the file.

Step 4: Configure ir-keytable

To configure ir-keytable, you will need to create a new file in the /etc/ir-keytable directory. This file will contain the configuration settings for ir-keytable.

Create a new file called ir-keytable.conf in the /etc/ir-keytable directory using the following command:

sudo nano /etc/ir-keytable/ir-keytable.conf

Add the following configuration settings to the file:

begin
  name  anysee_e30
  bits           32
  eps            30
  aeps          100
  one           0
  zero          0
  pointer       up
  repeat       1
  repeat_fast   2
  toggle_bit   0
  space         0
  begin
    name  anysee_e30
    bits           32
    eps            30
    aeps          100
    one           0
    zero          0
    pointer       up
    repeat       1
    repeat_fast   2
    toggle_bit   0
    space         0
  end
end

Save and close the file.

Step 5: Load the ir-keytable Module

To load the ir-keytable module, you will need to create a new file in the /etc/modules directory. This file will contain the module settings for ir-keytable.

Create a new file called ir-keytable.conf in the /etc/modules directory using the following command:

sudo nano /etc/modules/ir-keytable.conf

Add the following module settings to the file:

ir-keytable

Save and close the file.

Step 6: Test the Configuration

To test the configuration, you will need to restart the LIRC and ir-keytable services.

Restart the LIRC service using the following command:

sudo service lirc restart

Restart the ir-keytable service using the following command:

sudo service ir-keytable restart

Once the services have restarted, you can test the configuration by pressing a button on the infrared remote control. You should see the corresponding bash command issued on the console.

Conclusion

In this article, we have covered the process of adding LIRC to ir-keytable protocols on Debian and Raspbian systems. We have also covered the setup of the IR receiver device, an USB device included in the Anysee e30 Combo plus DVB-T tuner. By following these steps, you should be able to issue bash commands on infrared remote control button presses.

Troubleshooting

If you encounter any issues during the configuration process, you can try the following troubleshooting steps:

Check the IR receiver device is properly connected to the system
Check the LIRC and ir-keytable services are running
Check the configuration files for any errors
Check the console output for any error messages

Q: What is LIRC and how does it work?

A: LIRC (Linux Infrared Remote Control) is a software package that allows you to use infrared remote controls with your Linux system. It works by receiving infrared signals from the remote control and translating them into keyboard events or other actions.

Q: What is ir-keytable and how does it work?

A: ir-keytable is a utility that allows you to configure and manage infrared remote controls on Linux systems. It works by reading the configuration files for the remote control and translating the infrared signals into keyboard events or other actions.

Q: How do I configure LIRC and ir-keytable?

A: To configure LIRC and ir-keytable, you will need to create configuration files for the remote control and load the LIRC and ir-keytable modules. You can find more information on how to do this in the previous article.

Q: What are the benefits of using LIRC and ir-keytable?

A: The benefits of using LIRC and ir-keytable include:

The ability to use infrared remote controls with your Linux system
The ability to configure and manage infrared remote controls
The ability to translate infrared signals into keyboard events or other actions

Q: What are the limitations of using LIRC and ir-keytable?

A: The limitations of using LIRC and ir-keytable include:

The need for a compatible infrared remote control
The need for a compatible Linux system
The need for proper configuration and setup

Q: How do I troubleshoot issues with LIRC and ir-keytable?

A: To troubleshoot issues with LIRC and ir-keytable, you can try the following steps:

Check the IR receiver device is properly connected to the system
Check the LIRC and ir-keytable services are running
Check the configuration files for any errors
Check the console output for any error messages

Q: Can I use LIRC and ir-keytable with other Linux distributions?

A: Yes, you can use LIRC and ir-keytable with other Linux distributions, including Ubuntu, Fedora, and CentOS.

Q: Are there any alternatives to LIRC and ir-keytable?

A: Yes, there are alternatives to LIRC and ir-keytable, including:

irrecord: a utility for recording infrared remote control codes
irsend: a utility for sending infrared remote control codes
lircd: a daemon for managing infrared remote controls

Q: How do I uninstall LIRC and ir-keytable?

A: To uninstall LIRC and ir-keytable, you can use the following commands:

sudo apt-get remove lirc
sudo apt-get remove ir-keytable

Conclusion

In this article, we have covered some frequently asked questions about LIRC and ir-keytable. We hope this information has been helpful in answering your questions and providing a better understanding of how to use these tools.

Additional Resources

For more information on LIRC and ir-keytable, you can visit the following websites:

You can also find more information on how to use LIRC and ir-keytable in the following documentation: